Hi. What are you looking for? Tell us what you need and we'll get back to you.
Drum Handling
Drum handling gear covers adaptors, dollies, trolleys, and taps for moving and dispensing from 205-litre drums. The adaptors listed here — DIN 61, Berg 58mm, Mauser 69mm, US Buttress 64mm, Trisure 56mm — fit different drum neck threads, so check your drum brand before ordering. Dollies let you shift full drums without a forklift; trolleys tip and pour. Taps give you controlled flow for decanting oils, coolants, or chemicals straight from the bung.
Showing all 10 results
-
Not yet ratedSealeyAluminium Drum Wrench- Fits 2" & 3/4" BSP drum plugs
- 270 mm length
€31.91€32.23€25.94€26.20 -
Not yet ratedSealeyDrum Lifter 350kg Capacity- 350kg capacity
- Lifts 205L drums
- Keeps drum vertical
€190.21€192.13€154.64€156.20 -
Not yet ratedSealeyDrum Lifter 500kg Capacity- 500kg capacity
- Fits 205L vertical steel drums
- Welded gripping hooks
€122.94€99.95 -
Not yet ratedSealeyDrum Trolley/Stillage 205L- Holds 205L drums
- Spring-loaded mechanism
- Four wheels, uneven surfaces
€547.90€553.44€445.45€449.95 -
Not yet ratedSealeyFloat Gauge- 3/4″ BSP thread for 205L drums
- Gauge face marked 0-210 litres
- Water-filled polyethylene float
€88.23€89.11€71.73€72.45 -
Not yet ratedSealeyForklift Drum Clamp 350kg Capacity- 350kg capacity
- Fits 205L drums
- Steel construction
€553.44€449.95 -
Not yet ratedSealeyGator Grip Forklift Drum Grab 400kg Capacity- 400kg capacity
- Fits 205L steel drums
- Automatic grip lock
€654.46€661.06€532.08€537.45 -
Not yet ratedSealeyHydraulic Drum Truck & Van Loader 205L- 205L drum capacity
- Foot-operated hydraulics
- 800 mm width, 700 mm inside
€999.31€812.45 -
Not yet ratedSealeyHydraulic Drum Truck 205L- Hydraulic ram clamps and lifts
- 205L drum capacity
- 2 wheels + 1 braked castor
€608.79€614.94€494.95€499.95 -
Not yet ratedSealeyMobile Drum Handler 205L- Suitable for 205L drums
- 2 wheels + 1 braked castor
€662.06€668.75€538.26€543.70
Drum adaptors are machined to match specific manufacturer threads. DIN 61/31 is the most common European standard (61mm diameter, 31mm long thread), found on steel drums from suppliers across Europe. Mauser drums use a wider 69mm neck; Berg a narrower 58mm. US Buttress (64mm) suits American-spec drums, common on imported lubricants. Trisure (56mm) is less frequent but still turns up on specialist chemical containers. An adaptor that doesn't match the thread will cross-thread or leak under pressure, so measure the drum neck or check the manufacturer's spec sheet before fitting a pump or tap.
Dollies and trolleys handle the weight. A 205-litre drum of oil weighs over 180kg when full — too much to shift safely by hand. A drum dolly is a low platform on castors; you tip the drum onto it and roll. Models with a handle give you steering control on uneven floors. A drum and barrel trolley grips the drum upright, then tilts it for pouring; useful if you're decanting into smaller containers or filling equipment directly. Check the wheel type: hard nylon suits smooth concrete, soft rubber grips better on rough or painted surfaces but wears faster.
Taps thread into the 3/4-inch BSP bung hole (standard on most steel drums). Brass or zinc die-cast bodies resist corrosion from oils and water-based fluids; lockable taps prevent accidental discharge or tampering. Flow rate depends on the tap's bore and the fluid viscosity — a thin hydraulic oil will run faster than a heavy gear oil through the same tap. If you're dispensing flammable liquids, earth the drum and use a bonding strap to the receiving container; static discharge is a real ignition risk with low-conductivity fuels and solvents.